Recent content by gulfcoastkustom

Looking for a transmission adapter and bellhousing for a Dodge NV4500. If you have other parts such as flywheel, fork, throw out bearing, input shaft etc. I may be interested in those as well if the condition is good. Needing parts to swap a GM NV4500 behind a Cummins 4BT. Thanks in advance.

Looking to ship a 1926 ford body on a custom frame with dually rearend and 12v cummins sitting in it. Vehicle is not in running condition. 7' wide (with duals on rear that can be taken off) and 15' long. Looking to have it shipped in the the next couple of weeks or sooner.

Hoping for some helpful input please gang. I just replaced my stock HX35 for an industrial injection phatshaft series 66/74/14 turbo. I have 30psi fuel pressure at my pump, 4kgsk, tork tek ofv, rack plug, no fuel plate, afc slid all the way forward, star wheel all the way out, 7x.010 injectors...

Do I NEED to replace or upgrade my stock retainers while installing 110# valve springs? I have a 4K gov spring kit but was curious if better quality retainers are actually needed. Truck is just a daily driver that will not see 4K rpm very often.

Do you have a 2nd gen CTM (central timer module). Its the black box under the dash, drivers side, just above the go pedal. The one I need has to have a green connector port and a white connector port. Thanks!

I have a few parts laying around from my 2000 ram that I would like to get rid of: -Stock mirrors, power and heated -Stock air intake with K&N filter -Stock radio with cassette and CD player -Stock tailights All parts were in good working order when removed. I don't know what this stuff is...

I have a 2000 Ram 2500 quad cab short bed 4x4 that I need shipped from Niceville, FL to Albuquerque, NM around May. I am doing this well ahead of time to see what my prices and options would be. I can provide a more accurate date if someone thinks they can take the shipment. The truck is not...

Can anybody help me out with the years that the dash bezel will interchange? I purchased a bezel off of ebay for my 2000 ram and now the seller is telling me that it will only fit up to a 99.5. Is this a true statement? I was under the impression that 98-02 were the same.

I started puking a good amount of oil from my breather tube today on my way home from work at highway speeds. I noticed that my air is only coming out of the defrost vents as well. Truck is still running great with no excessive smoke or loss of power. Can my problems be related? The only thing I...

My park lights and dash lights stay on when the batteries are connected. I have tried pulling fuses, relays and the headlight switch itself and the lights still stay on. I noticed that the trailer relay clicks as soon as I connect the batteries as well. The only way I have found that kills...

Hey guys, once again I am relying on some feedback on how to proceed with my truck. I have a 2000 QCSB 24v 6 spd manual with a p pump (not sure what hp the pump is though). Other than the pump, I have a MBRP 4" high flow exhaust and a 4KGSK. Everything else is bone stock including the timing...

I just got my truck back together after my swap and I have an oil leak already! I used all new gaskets but must have not gotten a good seal on the tappet cover because it is drenching the drivers side of my motor. Has anybody ever attempted to replace the cover gasket with the p pump still...

I recently had a reman NV5600 put in my truck. Truck is a 2000 so it had the 1 1/4" input shaft. I had everything swapped over to accommodate the newer style 1 3/8" input shaft. I have only put around 100 miles on the truck since the trans work was done. I have a nasty grind going into 4,5,6...

This is what my circuit board from the overhead console looks like. If you have one like it I would like to purchase it.

I posted a picture of what my circuit boards look like. I appreciate the responses I have gotten from folks but I am still new on this site and don't have enough posts to be able to reply to the PM's I have gotten. If this looks like something you have and you want to sell it, please let me...