Search results

Anyone have the inside diameter of a stock steel 17 inch dually wheel?

Anyone have the maximum outside diameter measurement of a Dana 80 brake drum?

Anyone have a recent link to the factory 11.5/11.8 finned aluminum differential covers? I know they were around $115 at one time but everywhere I have found them they are almost $200 now.

Can anyone in Ohio build a set or possibly have a set they want to sell? 2 would be ok but 4 would be better...

Figured I'd cross post this here from the Dodge section cause of people using spacers on various pulling setups. Truck will still have drum brakes and springs. What all is required to run dually wheels on a 96 Dana 70? I'm assuming the wheels won't clear the drums, how big of spacers are...

What all is required to run dually wheels on a 96 Dana 70? I'm assuming the wheels won't clear the drums, how big of spacers are required per side? I want to run dually wheels on my 70 cause it's cheaper than finding a 80 and I won't be towing anything heavy with it.

What is the best tuner for a 07 ISX? The truck is 9400i International with a 435 horse engine, 10 speed and 3.58 rear gears...

What would a normal flat rate hours be for Replacing a front crank seal on a N14? Replacing an accessory drive seal on a N14? Replacing all 4 intercooler boots? Replace a clutch brake? Remove a fan assembly and replace it, including the adjuster and clutch? An oil change and chassis lube...

I can buy the complete kit new for $1,400.00 brand new shipped, normally the kit is around $3,000.00, is it worth it for a fairly stock 12 valve? And yes it's from a reputable dealer, they are just clearing their stock out...

I've Already Got A Pittsburgh Power 7 Stage Tuner On It. Any Other Tips Or Tricks To Make It Run Better? I Figure With The Tuner Its Around 600 To The Crank. It Will Get About 7Mpg On The #4 Fuel Mileage Setting. Its In A 1996 9400 International With A 9 Speed Trans..

What Are The Differences Between Automatic And Manual Transmission Truck Transfercases ? I need To Change Out The DLD In My 96 Automatic Truck. Sorry For The Capitalized Letters, One Of The Problems Of Owning An Android Phone...

A friend of mine is wantung to put a turbo kit on her 93 5 speed 7.3 truck and another friend of mine has a 6.9 with a turbo kit on it, will everything swap over to the 7.3???

Could the front suspension from a 350 bolt directly in place of a 150? I'm thinking about converting my 93 reg. cab short bed 150 into a dually using a complete F350 parts chassis I have, I've actually got almost all the parts to make it a Powerstroke 5 speed truck but thats too much work, I may...

I'll not mention the shop (from south Florida) that has its sticker in the back window of the truck or the fact their employee that did the install loves butt connectors and electrical tape.. I'll list the known issues... 1. Wiring to interface eveything from the gas truck to the 12 valve/47RE...

Any interest in a two or three speed transfercase that is 100% aftermarket and 100% American made? These are a completely new design and they are being built to take tremendous abuse. Think of it as a superior version of an Atlas II or a Stak Monster Box. Multiple selectable gear ratios and...

I'm about to pick up a new project truck. It's a 89 F350 with a Cummins and a 5 speed Getrag swapped in. I'm buying a Getrag with a Ford 205 bolted on it with an Advance Adapters adapter between them. I've got a ball-joint Dana 60 from a 1996 F350 SRW that I plan on using for a front axle. I'm...

Friend of mine has a early model 99 Extended cab short bed automatic push button 4x4 truck. Here are the symptoms... Extended crank to get started, roughly 12 seconds, then fires and idles fine. Drives fine till it gets to 40-45 mph then shuts off once shifting into overdrive, almost...

My 90 2wd D250 Regular cab long bed plows the front tires any time you turn more than a few inches like you were running a spool in the rearend. We jacked up the rear on one side and it only spun the one tire when put in gear. So we know the rear isnt locked. The rear does have a limited slip in...

I'm looking for a single engine modified tractor. Preferably a bare rolling chassis, I'd pay more if it had a set of cut 30.1's on it. This is going to be a project for next fall since my race car is about done...

I took all the bolts off and it slid back about 1/4 inch out of the aluminum adapter but wont go any further, its like its caught on something inside and I dont want to break the adapter prying on it... 1990 2wd auto...